https://www.psiconversion.com/products/engine-controller-kits/geniv/4L60E/

My Cart

Customers also purchased

Subtotal
$0.00

07 - 14+ Gen 4 LS/Vortec (58X) With 4L60E-75/4L80E engine controller kit

$1,499.00

APPLICATION: 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014 58X LS2 6.0 Corvette & Trailblazer SS, LS3 6.2, GMPP LS376 480 & 525, LS7 7.0 Corvette & Camaro ZL1, Vortec LY6, L92, L76, LMG, 4.8, 5,3, 6.0 and 6.2 engines with 4L60E-75/4L80E transmissions.

CLICK FOR COMPONENT ID GUIDE

SEE DESCRIPTION BELOW FOR INCLUDED PARTS


Read More
MODEL
ENGINE SIZE
TRANSMISSION TYPE
CAM SENSOR TYPE
INTAKE MANIFOLD / MAP SENSOR TYPE
FUEL INJECTOR TYPE
ALTERNATOR TYPE
SELECT LOOM TYPE
ADD PCM MOUNTING BRACKET
CHOOSE A PEDAL TYPE
ENGINE TO CHASSIS GROUND STRAP KIT (RECOMMENDED)
ADD FLEX E85 FUEL SIGNAL WIRE
LS ENGINE GAUGE INSTALL KIT (For Factory Gauges)
ADD FUSE BLOCK MOUNTING BRACKET
ADD 4X4" DIAMETER MAF Tube
Sold Out! Pre-order Now
SKU: KIT-1028
KIT-1028
Remove from wishlist Add to wishlist
Have questions, on a time crunch, or just need this quick?          Give us a call: 732-276-8589                                                              Email: CustomerService@PSIConversion.com
  • APPLICATION: 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014 58X LS2 6.0 Corvette & Trailblazer SS, LS3 6.2, GMPP LS376 480 & 525, LS7 7.0 Corvette & Camaro ZL1, Vortec LY6, L92, L76, LMG, 4.8, 5,3, 6.0 and 6.2 engines with 4L60E-75/4L80E transmissions.

    CLICK FOR COMPONENT ID GUIDE

    SEE DESCRIPTION BELOW FOR INCLUDED PARTS

    PARTS INCLUDED:
    Complete engine wiring harness (4 Wire Hookup), programmed engine controller (PCM-1009), programmed transmission controller (TCM-1001), accelerator pedal (ACC-1007), LS3 cartridge mass air flow sensor (ACC-1005), mass air flow sensor holder (ACC-1006), oxygen sensors x2 (ACC-1003).

    NOTES: This COMPLETE controller kit from PSI includes everything you need to get that gen 4 LS/Vortec engine and transmission running in your project vehicle. Why use an aftermarket controller for your transmission when you can utilize the Factory controller just like the original vehicle! The kit includes hardware and components that don't typically come with used engines, such as the wiring harness, mass airflow sensor, oxygen sensors, brake switch, and programmed PCM which includes the mounting bracket - eliminating the need to source them separately. This controller system is a true stand-alone system for use in older vehicles, as all that's needed to get a vehicle running with it are power and ground sources, a fuel pump able to support 58-psi (400 kPa) at the fuel rail, and an electric cooling fan.

    CONNECTIONS FOR:
    • Fuse/Relay Box
    • Fuel Pump Control (Relay included)
    • Fan controls (Relays and fuse available separately KIT-1010)
    • Check Engine Light, Speedo output, Tachometer, OBD2 Port
    • IAC and TPS on DBC setups
    • MAF Sensor
    • MAP Sensor
    • Engine Coolant Temp Sensor
    • Alternator Control
    • (2) Upstream Oxygen Sensors
    • Crankshaft Position
    • Camshaft Position
    • Fuel Injectors
    • Coil Pack Sub-Harness
    • Automatic or Manual Transmission control
    • Knock Sensors
    Connections from the Harness You Will Need to Hookup:
    • Fuel Pump (Required)
    • Switched Ignition Power (Required)
    • Malfunction Indicator (Check Engine, MIL, CEL, ETC.)
    • Speedometer
    • Tachometer
    • Fan 1 Relay Control (Low Speed or Single Control)
    • Fan 2 Relay Control (High Speed or Second Fan Control)
    • Fan Relays available separately KIT-1010

    WARNING: The installed tune is a base/startup tune, mirroring a factory OEM tune based on the options selected in your order. The tune will remove the VATS (Vehicle Anti-Theft System), bypass VVT (if applicable), disable DOD (if applicable), and remove any restrictions preventing operation of the engine when installed in a different vehicle.

    If the engine has a different camshaft, ANY performance modifications, or has any components that differ from options selected on your tune request the following issues may occur: No start, erratic idle, surging, check engine lights, limp mode, lack of shifting, no throttle response, poor power delivery, and other issues possibly rendering the engine inoperable. Any engine or transmission modifications will REQUIRE a custom tune to ensure proper operation and prevent serious damage. PSI Conversion cannot be held responsible for issues related to operation or performance when the engine/transmission has been modified, or varies from the options selected when the tune was installed.

    These harnesses are designed for retrofitting 2007 - 2014 58X LS2 6.0 Corvette & Trailblazer SS, LS3 6.2, GMPP LS376 480 & 525, LS7 7.0 Corvette & Camaro ZL1, Vortec LY6, L92, L76, LMG, 4.8, 5,3, 6.0 and 6.2 engines and 4L60E/80E automatic transmissions into older muscle cars and street rods or newer non-emissions controlled vehicles. They are completely plug and play with four wire hookup (switched power, constant power and ground connections required). Harnesses are designed with a sliding grommet seal and 4 - 5 feet of length from the rear of the cylinder head to the PCM mounting position under the vehicle dashboard. A sliding grommet seal allows for professional, leak proof installation.

    Harnesses are professionally constructed from brand new GM Delphi connectors and TXL (Polyethylene cross linked) high temperature wire to GM specifications.

Customers Also Purchased These Related Items

Subscribe

Sign up to get the latest on sales, new releases and more …