My Cart

Customers also purchased

Subtotal
$0.00

01 - 02 Gen 3 Vortec (24X) Drive by wire 4L60E-75/4L80E Standalone harness w/ 6+2 connector throttle

$624.00
(5)

APPLICATION: 2001 & 2002 Vortec Engines (DRIVE BY WIRE ONLY) w/ 4L60E-75/4L80E transmissions for use with RED/BLUE 411 P01 PCM.

PARTS INCLUDED: Complete engine and transmission Harness, Instruction Manual              

NOTE: A 2001 & 2002 truck has a 2 connector throttle body (see image).


Read More
TRANSMISSION TYPE
THROTTLE BODY TYPE
CHOOSE INJECTOR TYPE
INTAKE MANIFOLD / MAP SENSOR TYPE (WIRING ONLY)
ADD A PEDAL
AC RECOGNITION (IDLES ENGINE UP)
CRUISE CONTROL
ADD E85 FLEX FUEL SIGNAL WIRE
SELECT LOOM TYPE
ADD TCC/BRAKE SWITCH KIT
ADD (2) O2 SENSORS (SAVE $5)
ENGINE TO CHASSIS GROUND STRAP KIT (RECOMMENDED)
ADD FUSE BLOCK MOUNTING BRACKET
Sold Out! Pre-order Now
SKU: HAR-1084
HAR-1084
Remove from wishlist Add to wishlist
Have questions, on a time crunch, or just need this quick?          Give us a call: 732-276-8589                                                              Email: CustomerService@PSIConversion.com
  • APPLICATION: 2001 & 2002 Vortec Engines (DRIVE BY WIRE ONLY) w/ 4L60E-75/4L80E transmissions for use with RED/BLUE 411 P01 PCM.

    PARTS INCLUDED: Complete engine and transmission Harness, Instruction Manual              

    NOTE: A 2001 & 2002 truck has a 2 connector throttle body (see image). If using a (8 PIN) connector throttle body use PSI harness HAR-G3WA

    ADDITIONAL ITEMS REQUIRED: RED/BLUE 411 P01 PCM

    CONNECTIONS FOR:
    • Fuse/Relay Box
    • Fuel Pump Control (Relay included)
    • Fan controls (Relays and fuse available separately KIT-1010)
    • Check Engine Light, Speedo output, Tachometer, OBD2 Port
    • IAC and TPS on DBC setups
    • MAF Sensor
    • MAP Sensor
    • Engine Coolant Temp Sensor
    • Alternator Control
    • (2) Upstream Oxygen Sensors
    • Crankshaft Position
    • Camshaft Position
    • Fuel Injectors
    • Coil Packs
    • Automatic or Manual Transmission control
    • Knock Sensors
    Connections from the Harness You Will Need to Hookup:
    • Fuel Pump (Required)
    • Switched Ignition Power (Required)
    • Malfunction Indicator (Check Engine, MIL, CEL, ETC.)
    • Speedometer
    • Tachometer
    • Fan 1 Relay Control (Low Speed or Single Control)
    • Fan 2 Relay Control (High Speed or Second Fan Control)
    • Fan Relays available separately KIT-1010



    NOTES: These Harnesses are designed for retrofitting 2001 & 2002 Vortec engines (4.8, 5.3, 6.0) and 4L60E-75/4L80E transmissions into older muscle cars and street rods or newer non-emissions controlled vehicles mated to a RED/BLUE 411 P01 PCM. Harness allows use of the factory Vortec intake manifold and Multec Injectors, flex-fuel Injectors (EV6) or EV1 injectors. They are completely plug and play with four wire hookup (switched power, constant power and ground connections required) for engine and transmission. Harnesses are designed with 4 - 5 feet of length from the rear of the cylinder head to the PCM mounting position under the vehicle dashboard. A sliding grommet seal allows for professional, leak proof installation.

    Harnesses are professionally constructed from Brand New GM Delphi Connectors and TXL (Polyethylene Cross Linked) High Temperature Wire to GM Specifications. All Harnesses are 100% Quality Inspected prior to shipping. All Harnesses require PCM VATs removal, available through PSI. Please contact PSI for more information.

    • OMG, where have you been
      I don't know where to start. I had an old harness reworked and all I did was fight with the vehicle and everything about it. I had problems with model numbers, intake, throttle drive by wire, and a few other applications that just did not make sense. When ordering a new wiring harness from PSI it became perfectly clear that they not only had all the information that I needed, but they also modeled numbers of different parts, everything became so much easier. Not only did I get an excellently made wiring harness, I also received a sheet with all the information for all the other parts that I need to put my motor together and make this possible. The ordering was very simple and the representative was extremely knowledgeable. If I had to do it all over again I would have just called PSI in the 1st place and asked what would be the best application for what I'm trying to build. In a nutshell, the LS swap went very well once I got my parts from PSI. Every single connector had just enough length to connect to what I had on the engine. I cannot say enough about PSI the tech the equipment and the overall experience please thank your entire PSI team that made this build possible for me I appreciate your patience your expertise and knowledge. Happy holidays.
      Duane

      -

      Ontario, CA.

      Was this review helpful?

    • Very good harness
      First time I used this harness and I was impressed with the quality and ease to install.
      Harrold

      -

      Cave Creek, AZ.

      Was this review helpful?

    • My Harness
      This harness is amazing. It was easy to install, the instructions were on point. The tech team is great. My only issue was my MAF sensor was to short. I was able to buy an 18” extension, which I am ok with. I was hoping after spending what I did on my harness maybe I could have got it free of charge. Or at least free shipping… but definitely would NOT write them off for this! There product is amazing! Fired up on the first try

      We'll get you hooked up on the next one- let us know if you see us @ a show or order again - PSI
      Whodoesit85

      -

      Denver

      Was this review helpful?

    • Wiring harness and computer
      Works flawlessly, wiring looks as great as it works. Didn’t have any problems at all, installs easy and simple. Very knowledgeable and pleasant to work with. They will answer any question you may have. Great product. 
      Anyelo Garcia

      -

      Sunrise, Fl

      Was this review helpful?

    • Can't go wrong on your project with PSI.
      I used a old harness cut up at first . Bought a PSi harness. Can't compare how it runs. Dont make the mistake i did. Waist money. PSI is on it . Worth every penny. Quality.
      SD619BLAZER73

      -

      San Diego, CA

      Was this review helpful?

Customers Also Purchased These Related Items

Subscribe

Sign up to get the latest on sales, new releases and more …